Safety data sheet for Isopropyl myristate

CAS 110-27-0

This is the free preview of a draft SDS for Isopropyl myristate — Sections 1, 2 and 9, generated from the sources named below. The full 16-section draft, with your own company in Section 1, is $5 per document.

Typically documented by: Cosmetic emollient, fragrance carrier.

Draft safety data sheet — preview

Sections 1, 2, 9 of 16

CAS number
110-27-0
Molecular formula
C17H34O2
Molecular weight
270.5 g/mol
Signal word
Warning

Hazard classification

  • GHS07 — Exclamation mark — irritant
  • H315: Causes skin irritation.

Section 1 — Identification

1.1 Product identifier

Product identifier: Isopropyl Myristate

Chemical name (IUPAC): propan-2-yl tetradecanoate

CAS number: 110-27-0

PubChem CID reference: 8042

Synonyms: ISOPROPYL MYRISTATE; Isopropyl tetradecanoate; Isomyst; Bisomel; Estergel; Deltyl Extra; Kesscomir; Promyr; Tetradecanoic acid, 1-methylethyl ester; Crodamol IPM

Section 2 — Hazards Identification

2.1 Classification of the substance or mixture

Classification basis: OSHA 29 CFR 1910.1200 Appendix A, aligned to the GHS Rev. 7 hazard classes this sheet resolves: Skin Irrit. 2.

Classification: Skin Irritation, Category 2 (Skin Irrit. 2) [H315] (single source)

Second-source corroboration: no second public classification source on file holds this CAS.

The rows marked (single source) rest on PubChem aggregated supplier notifications alone.

2.2 Label elements

Signal word: Warning

GHS pictograms: GHS07 (Exclamation)

Hazard statement: H315: Causes skin irritation.

Precautionary statement: P280: Wear protective gloves, protective clothing, eye protection and face protection.

Precautionary statement: P264: Wash hands thoroughly after handling.

Precautionary statement: P302+P352: IF ON SKIN: Wash with plenty of water.

Precautionary statement: P362+P364: Take off contaminated clothing and wash it before reuse.

Precautionary statement: P332+P313: IF SKIN irritation occurs: Get medical advice/attention.

Section 9 — Physical and Chemical Properties

9.1 Information on basic physical and chemical properties

Physical form: Liquid

Appearance: Liquid of low viscosity

Odor: Practically odorless

Boiling point: 315°C (599°F) at 1013 hPa

Melting point: 3°C (37°F)

Density: 0.8532 g/cm³ at 20°C

Vapor pressure: 0.012 Pa at 25°C

Water solubility: Insoluble in water and glycerol

Log Pow (log Kow): 7.2 (calculated)

Not stated in the sourced records: Flash point, Vapor density, Lower explosive limit, Upper explosive limit, Auto-ignition temperature, Viscosity, pH.

Where each value came from

Odor — Hazardous Substances Data Bank (HSDB)
O'Neil, M.J. (ed.). The Merck Index - An Encyclopedia of Chemicals, Drugs, and Biologicals. Whitehouse Station, NJ: Merck and Co., Inc., 2006, p. 902
View the record
Boiling point — Hazardous Substances Data Bank (HSDB)
Daubert, T.E., R.P. Danner. Physical and Thermodynamic Properties of Pure Chemicals Data Compilation. Washington, D.C.: Taylor and Francis, 1989
View the record
Melting point — Hazardous Substances Data Bank (HSDB)
Same reference as odor above.
View the record
Density — Hazardous Substances Data Bank (HSDB)
Same reference as odor above.
View the record
Vapor pressure — Hazardous Substances Data Bank (HSDB)
Same reference as boiling point above.
View the record

A value with no row here was assembled from more than one record, so no single record is credited for it. The draft you buy carries this table as an appendix covering all 16 sections.

Sources

  • Hazardous Substances Data Bank (HSDB)
  • PubChem — GHS classification
  • PubChem — compound record
  • PubChem — names and identifiers
  • PubChem — regulatory information
  • PubChem — toxicity data

Sections 1.3 and 1.4 are withheld here because the supplier and emergency contact blocks carry your own company details in the draft you buy. Every draft needs review by a competent person before it is issued.

Measured values for Isopropyl myristate, and where each one comes from

8 measured values for 6 properties, read from 2 public databases. On 2 properties the records differ. Each reading is shown with its own record. Follow any linked record to read the value at its source.

Boiling point

1 record

Used with vapour pressure to judge how readily the substance reaches the air you breathe.

588 K (315 °C) at 760 mm Hg
Hazardous Substances Data Bank (HSDB)

Melting point

1 record

Fixes the physical state at handling temperature, which the label and the transport class depend on.

Vapour pressure

2 records differ

The higher it is, the faster the substance evaporates into the workplace air at room temperature.

9.35X10-5 mm Hg at 25 °C
Hazardous Substances Data Bank (HSDB)

Density

2 records differ

Needed to convert between mass and volume on the label, in transport papers and in a spill estimate.

Solubility

1 record

Determines spill behaviour, the right extinguishing media and the correct first-aid rinse.

Soluble in ether, very soluble in acetone, benzene; insoluble in water
Hazardous Substances Data Bank (HSDB)

Odour

1 record

Odour is a warning property only. Many substances are hazardous well below the concentration you can smell.

These are the public records read for Isopropyl myristate, published here unchanged. Where two records disagree, the draft you buy states the value and names the record behind it, so a reviewer can see what was chosen. Every draft needs review by a competent person before it is issued.

Get the full draft SDS for Isopropyl myristate

The draft covers all 16 sections under OSHA 29 CFR 1910.1200 and GHS Rev. 7, or the CLP EC 1272/2008 layout for the EU. Each draft arrives as an editable Word .docx with an appendix naming the source of each value, in about 60 seconds. $5 per document, no account.

Intake

Safety Data Sheet (SDS) — $5 per document

Confirm the compound and the document, then continue to checkout. Every document is delivered as a draft for professional review.

Safety Data Sheet (SDS)US OSHA HazCom format · editable .docx draft

A CAS number or a chemical name.

Standard known chemicals only. A mixture or an unlisted compound stops before checkout and routes to the free mixture classifier (a declared formula can be bought there as a $5 EU-format draft) or Custom SDS on Pro.

We deliver the draft to this address, normally within 60 seconds.

Branding and formatOptional — default branding, US format

Used to white-label the draft. Leave blank for default branding.

Format

Guest checkout through Stripe. Every document is a draft for review by a qualified EHS professional before you put it to use.